Toilets are an essential part of our houses. They should be regularly cleaned and well maintained to ensure that high hygiene standards are kept. Cleaning of a toilet siphon jet is the most crucial part of cleaning your toilet, isn’t it? Therefore, you need to use the right procedure and the right cleaning products for you to be successful. At one time you may have experienced slow flashing, haven’t you? It is very frustrating. You need to cut off such frustrations by properly cleaning of your toilet siphon jet. Today I discuss in this article how to clean toilet siphon jets.
What is a siphon jet and Its Role?
A toilet siphon jet is a cast pocket used in crofting extra water until you flash your toilet. When flushing has been initiated there is a vacuum created that puts more pressure on this extra water to come out of the pocket. Moreover, the pressure proportionally increases the flushing pressure. Water is becoming a rare commodity, especially in cities, isn’t it?
Having a good toilet siphon jet will increase the pressure of flushing without using a lot of water. For a toilet siphon jet to work efficiently you must always find a modest way to clean it. The cleaning also should be regular
Signs of a clogged toilet Siphon Jet and how to check for clogs
Slow flushing is the main sign that your siphon jet is clogged. When the rim jets are clogged with mineral substances such as calcium the flow of water especially from the toilet tank to the bowl may be hindered.
The procedure of Cleaning A Toilet Siphon Jet
Materials Required
- Alcohol-based Gel (Vinegar)
- A base substance (Baking soda)
- A Funnel
- Sponge material
- A Bucket
- L-shaped 3/16’’ Allen wrench
- Rubber gloves
- Toilet brush
- Toothbrush
Stages to follow: How to clean toilet siphon jet
Stage 1: Remove All the Water from The Bowl
To clean siphon Jet you need an alcohol-based gel, and in our case, I advise the use of vinegar. For the vinegar to work directly with the mineral deposits in the siphon jet, you will need to drain the toilet tank and the Siphon Jet. Make sure that you turn off the water supply to the tank. This can be done by either turning the shaft valve in a clockwise direction or pulling the shaft valve all the way out in case you have a pull and push valve.
When flushing the toilet, you need to hold the flashing handle until all the water drains. Thereafter, using a sponge material you can dry the tank gently. For safety measures, you will need gloves because the water is not clean. You must have realized that whenever you flash a toilet some water remains in the Siphon jet, haven’t you? This is the water that prevents gases and smell from coming back from the sewer line or the septic tank. Now you can gently remove the Toilet bowl and place in in a safe place.
Step 2: You Need to Cover the Rim Jets with A duct Tape
If you look carefully into a toilet bowl either physically or using a mirror, you will see small holes. These holes are the rim jets. Moreover, if you need to know the degree of how dirty you siphon jet is, just confirm the amount of clog in the holes. Cover all the holes with duct tape. The reason for covering them is to stop the vinegar from flowing to the bowl as fast as the water. Instead, it will be trapped inside the rim and therefore eat away the calcium.
Stage 3: Use the Alcohol-Based Gel
Whenever there are mineral deposits on your toilet siphon jet and the rim jets, it means that your toilet tank is also clogged. If you clean both the rim jets and the siphon jet leaving out the toilet tank it means that it will not take long before you need to clean them again. You need to start your cleaning with the toilet tank by pouring enough vinegar that can be able to cover all the mineral deposits. After cleaning the tank now, you can pour more vinegar to the siphon jet and the toilet rims.
You will need to be careful when pouring the vinegar. You need a funnel to pour your vinegar. After you assemble the materials pour the vinegar using a funnel into the overflow pipe. The vinegar poured should be enough to cover the mineral deposits and replace the water that was in the bowl. The poured vinegar will be trapped in the toilet rim and the rest will flow into the bowl. For some designs of toilets, you will need to leave the vinegar for at least 12 hours for better results.
Muriatic acid, bleach and other chemicals can also be used instead of vinegar. It all depends on what you prefer. Following the same procedure, you will achieve the same results. However, these chemicals are not very friendly to some toilet parts especially those made of rubber. Corrosion may occur leading to wearing of the parts. The tank will eventually start leaking due to the effect of the chemicals.
Stage 4: How To Clean The Rim Jets
After a minimum of one hour, you can remove the duct tape and drain the vinegar. To ensure that your ream jets are mineral deposit free, use an Allen wrench to check if all the holes are clean. Put an Allen Wrench in each hole and rotate it to ensure that you clean all the rim jets. This also ensures that all the holes are wide open. I always prefer the L-shaped Allen Wrench since it is very flexible to rotate around the rim jets
Stage 5: Flash the Toilet
Since you need to push out the Vinegar out of the bowl through the unclogged rims you will need to flush the toilet. To Read how to unclogged the toilet when nothing works. The vinegar that was inside the bowl will be replaced by water. Mineral deposits that will be removed by the vinegar will also be washed out. Sometimes, the stains in your toilet may be so saturated therefore you can use a bottle to spray a disinfectant into the toilet tank
Stage 6: Add a Base
The vinegar that we use to clean the toilet is a strong acid. Therefore, we need to add a strong base and, in our case, I can suggest that we use baking soda. you to add the baking soda slowly for the reaction to take place effectively. One cup of baking soda is enough to neutralize the solution
Stage 7: How Clean the Toilet Tank
For best results, you will need a hand brush and a scrabbing sponge material to clean the siphon jet. More scrabbing will be required especially at the bottom of the toilet tank because this is where most mineral deposits accumulate hand brush may not be able to reach all corners of the bowl, therefore, you can use a small brush, for instance, a toothbrush to scrub all parts
Stage 8: Clean the Siphon Jet, Rim Jets and The Siphon Jet
Vinegar cannot remove all the mineral deposits from the siphon jet. Use a toilet brush to scrub the remaining mineral deposits and water stains. Just to confirm if there is any calcium left in the siphon jet you can use a finger to confirm. If any it will be removed by water since the vinegar will have loosened it.
Stage 9: Confirmation Point
Now turn on the water and let the toilet tank fill. The speed of how water flows into the bowl can enable you to rate how effective your cleaning was. If the toilet flushes as powerful as it should be then a great job has been done. If you do not achieve the expected results then you can repeat the process. Cleaning a toilet siphon jet has been that easy! Isn’t it?
Conclusion
Good hygiene is highly recommended by health experts. Toilet hygiene has proven to be very crucial. Regular cleaning of your toilet siphon jet will not only help you to achieve high hygiene standards but also your house will always be smelling nice. I hope that once you undergo the process you will be able to achieve whatever results you wanted.
You may have been wondering why won’t my toilet stay clean. The products you use to clean and the procedure may have been wrong but for now, you are covered. After Reading this article I think you now fully understand How to clean toilet siphon jet? If you have any query please contact with us. We will try to help with this issue.
FAQ: How to clean toilet siphon jet
Q: How can I clean my toilet rim jets?
Using an L-shaped Allen Wrench will be very helpful because it can easily rotate around the rim jets.
Q: Why does my Siphon Jet get clogged so fast after cleaning?
The main reason for this is always ignoring cleaning the toilet tank. There is also an accumulation of materials in the toilet tank that need to be removed whenever you clean your siphon jet.
Q: How often should I clean my toilet bowl?
After 72 hours of active usage of the toilet, you need to clean your toilet bowl.
Q: What should I use to clean my faucet?
Maintaining your faucet for long-term beauty is best done with a gentle touch. When cleaning, use only a soft cloth and water to keep dirt and dust from building up. For stubborn spots, use mild soap but avoid abrasive materials such as cleaners or cleaning pads that could scratch the delicate surface of your faucet’s finish.
Furthermore, chemical cleaners, including ammonia, can damage the protective clear coat, which could permanently scar the surface of your faucet – when in doubt about what to use for these items, it’s best to ask an expert! To ensure you can enjoy your fixture for years, take proper care when cleaning. What should I use to clean my faucet? Remember that water and a soft cloth are all you need.